Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
Listed here below you can get some very good insight in relation to How to Install a Bathtub Yourself.
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open a wall to get rid of the old bathtub as well as place the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will need a helper to vacate the old tub as well as set in the new one. Make certain you have qualified yourself for the task as well as are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your shower room if you have actually currently acquired a new bathtub and also do not require to change the setup of your previous water supply pipelines.
Your tools and product list need to comprise the following:
Preparing for the Installment
Firstly, the sustaining structure supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted access that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, put the bathtub in the required position. The wood boards are useful in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the bathtub up until the spirit level reviews level.
To mount faucets, fit all-time low of the outermost flexible faucet port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints and also new pipework for leakages and also tighten them if necessary. Fill the tub as well as also check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and securing around the bathtub ought to wait up until the tub has been used a minimum of once as this will settle it into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in place between the faucet as well as the sink. Safeguard the faucet in position with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind ought to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a rigid seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes and also cartridges, and also can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in use. The sealant can split relatively very early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that entry about A Step-by-Step Guide to Installing a Bathtub when browsing on the search engines. Liked our post? Please share it. Let someone else find it. Kudos for your time. Please check up our blog back soon.
Contact for excellence! Report this page